Casa > Blog > Problema comune > Design of constant force springs

Design of constant force springs

fonte:Precisione di Qianye volta:2022-9-14
 A constant force spring is a spring that exerts a constant force over its range of motion. That is, it does not obey Hooke’s law. Typically, a constant force spring is constructed as a coiled band of spring steel so that the spring relaxes when fully coiled. When it is unrolled, the restoring force comes mainly from the portion of the belt that is close to the roll. Since the geometry of this region remains nearly constant as the spring unfolds, the resultant force is nearly constant.
      By creating a spring with a variable pitch, you can make a push-shape spring with a constant velocity. Placing a larger pitch in a larger outer diameter coil and a smaller pitch in a smaller outer diameter coil will force the single spring to fold all coils at the same rate when compressed.
      Design of Constant Force Springs: A constant force spring is a coil of prestressed tape that exerts a nearly constant restraining force against unwinding (Figures 1 and 2). The force is constant because the change in the radius of curvature is constant. This is the case if the change in coil diameter due to buildup is not taken into account. Long reach, constant torque and virtually no friction have led many designers to specify constant force springs in applications such as sliding doors and windows and height adjustment of computer monitors and fans, store display shelves or motor carbon brush motors . Constant force motor springs are also used to drive mechanisms for timers, movie cameras and cable retractors.

      Tension type constant force tension springs are supplied in coils with a natural radius of curvature R (Fig. 3). If such a spring is installed on the drum, the drum diameter should be 10% to 20% larger than its natural diameter. There should be one and a half turns on the reel. The active portion of the material is approximately equal to 1.25 times the diameter D. Therefore, the spring will not reach its rated load until the elongation is greater than 1.25D (Figure 1). The radius of curvature of the active part goes from R to infinity and a clearance is required. The recommended distance from the center of the drum to the straight section is 0.8 times the diameter D (Figure 3). Strips can become unstable when stretched for extended periods of time and should be guided to prevent twisting or kinking during recoil. The diameter of the idler must be larger than the natural diameter and must not be used to reverse the natural radius of curvature (Figure 4).

Depending on your application, a constant force spring may be ideal. Consultation with the spring manufacturer for constant force springs is recommended at the design stage. Qianye Precision specializes in the production and manufacture of high-precision clockwork springs, which are widely used in various electronic devices, household appliances, small toys, office supplies, communication equipment, medical machinery, electronic computers, windows, doors, vehicles, etc. The imported raw materials and domestic raw materials will continue to meet your requirements. The company has more than 20 years of experience in product development, production and manufacturing, and has become a well-known brand distributor in China.

Ultime notizie

 Electric Fan Lifting Spring: An Innovative Solution for Enhanced Airflow
Electric Fan Lifting Spring: An Innovative Solution for Enhanced Airflow

Time:2023-5-2

Electric fans have become an indispensable component of our lives, providing a refreshing breeze during hot summer days. However, the design of the traditional electric fan has remained unchanged for decades, resulting in limited efficiency and airflow. To address this issue, a new innovation has emerged in the form of an Electric Fan Lifting Spring that offers enhanced airflow and...

 What are the factors that cause premature spring damage ?
What are the factors that cause premature spring damage ?

Time:2023-8-21

According to the informal statistics, the cycle life of high-quality springs can reach more than ten years or even longer under normal use. If the spring quality is not qualified, or there are some improper actions during using process, it may make the springs become premature useless. Then, let's take a look at the factors that cause the premature failure of the spring. Exceeding the specified...

 Tailored Springs: A Personalized Approach to Spring Manufacturing
Tailored Springs: A Personalized Approach to Spring Manufacturing

Time:2023-6-16

Springs are essential components in a wide range of industries, including automotive, aerospace, medical, and electronics, among others. They provide critical functions such as absorbing shock, controlling motion, and storing and releasing energy. However, not all springs are created equal, and their performance and longevity depend on their design, materials, and manufacturing processes. That's where tailored springs come in –...

 Design and Analysis of a Constant Force Torsion Spring
Design and Analysis of a Constant Force Torsion Spring

Time:2023-6-3

A torsion spring is a type of spring that works by twisting its ends. This twisting motion generates force that is proportional to the amount of twist. A constant force torsion spring is a torsion spring that has a constant force output over its entire range of motion. In this article, we will discuss the design and analysis of a...

 High quality Constant Force Torsion Spring: An Introduction to a Mechanical Powerhouse
High quality Constant Force Torsion Spring: An Introduction to a Mechanical Powerhouse

Time:2023-7-20

Introduction In the realm of mechanical engineering, springs play a pivotal role in a wide range of applications. One such type of spring that has gained significant recognition is the constant force torsion spring. This article aims to provide an in-depth understanding of this mechanical powerhouse, exploring its design, functionality, and various applications. Design and Construction of Constant Force Torsion...

 High Cycle Garage Door Springs: Durable and Long-lasting Solutions for Your Garage Doors
High Cycle Garage Door Springs: Durable and Long-lasting Solutions for Your Garage Doors

Time:2023-8-23

Garage doors play a vital role in providing security and convenience for homeowners. They not only safeguard our vehicles but also serve as an additional entrance to our homes. One crucial component of a garage door is the spring system, which supports the weight of the door and enables smooth and effortless opening and closing. When it comes to choosing...

Product
 Servizio di progettazione di ottimizzazione
Servizio di progettazione di ottimizzazione
Dalle idee di prodotto, dal design alla produzione del prodotto finito, possiamo assistere i clienti nel completarli e aiutare i clienti a ottimizzare i loro prodotti dal punto di vista professionale dell'uso primaverile, accelerare...
 Molla a forza variabile
Molla a forza variabile
Caratteristica: l'aspetto della molla a forza variabile e della molla a torsione variabile è molto simile alla molla a forza costante e alla molla a torsione costante. Le molle a forza variabile e le molle a torsione variabile possono...
 Servizi di montaggio e montaggio
Servizi di montaggio e montaggio
Qianye Company non fornisce solo la produzione di molle di precisione, ma si concentra anche sulla progettazione strutturale e sulle soluzioni funzionali dell'intero sistema di molle e può fornire un...
 Molla per spazzole di carbone
Molla per spazzole di carbone
Caratteristica: 1. A causa della forza costante, indipendentemente dalla lunghezza della spazzola di carbone e del collettore, la pressione rimane la stessa. 2. La molla a forza costante riduce la spazzola di carbone...
 Molla a torsione costante
Molla a torsione costante
Caratteristica: La molla a coppia fissa (costante) (molla) è realizzata in acciaio inossidabile. La forza esterna riavvolge la molla principale dal suo stato naturale alla ruota di uscita (accumulo di energia). Quando il...
 Primavera di potenza
Primavera di potenza
Caratteristica: la molla di alimentazione è avvolta da una striscia di acciaio. È necessaria una scatola a molla per limitarne il diametro esterno. Il centro della molla è collegato all'albero. Quando...