domov > Blog > Informacije o panogi > Uporaba vzmeti s konstantno silo v mehanizmu za uravnoteženje lastne teže naprave za vzorčenje

Uporaba vzmeti s konstantno silo v mehanizmu za uravnoteženje lastne teže naprave za vzorčenje

vir:Natančnost Qianye čas:2022-9-14

At present, various sample probes and reagent probes are used in medical laboratory equipment to suck samples, add samples, suck and test u, add reagents, measure and other operations. Most of the devices used in these action combinations are intelligent sampling devices, and the system used can automatically process data. Due to the full function and complex mechanism of the sampling device, the self weight of the system device is large, This brings higher and higher performance and power requirements to the driving motors of various sampling devices.

The self weight balance mechanism is set between the sampling device and the main structure and is composed of a lifting device and a vzmet s konstantno silo. The lifting device is composed of gears, racks and linear guide rails. The gears are driven by the motor and fixed on the main structure with the motor. The rack and the gear mesh to move up and down. The rack is fixed on the linear guide rail and the sampling device is fixed on the rack, The lifting device can also be composed of gear combination roller chain or synchronous belt, ball screw or flexible rope.

The upper end of the vzmet s konstantno silo is fixed on the main structure, and the lower end of the vzmet s konstantno silo is wound on a roll shaft on the sampling device. The roll shaft can rotate with the rise and fall of the sampling device. According to the height of the rise and fall of the sampling device, the excess part of the vzmet s konstantno silo can always be wound on the roll shaft. No matter how long the vzmet s konstantno silo is stretched, its own force wound on the roll shaft is constant, and the tension of the vzmet s konstantno silo is greater than or equal to the rack The sum of the gravity of the linear guide rail and the sampling device.

  Vzmet s konstantno silo is made of steel strip. When it is straightened by external force, the spring will naturally roll back and produce elastic force. The advantages of constant force spring over traditional wire spring are as follows:

  1.High elastic output can be achieved in a very small device space.

 2.Maintain a certain elasticity in all strokes. The preload stroke is short, that is, the required elasticity can be achieved through a short stroke. The original long-term is smaller than the line spring, and the stroke is unlimited.

  When designing or specifying a vzmet s konstantno silo, many basic engineering parameters need to be considered. Material, fatigue life, tensile load, torque and friction, speed and acceleration, installation, safety considerations and application environment are all key factors.

Shenzhen Qianye Precision Metal Co., Ltd. is a global spring manufacturer with more than 20 years of spring manufacturing experience. As a professional spring supplier, we can provide all kinds of spring springs, as well as the application design and solutions of all kinds of springs. We sincerely suggest that customers obtain consulting services from our R&D engineers at the initial stage of product introduction and development. Assist in product design, development and proofing according to your needs, so that your products can find the best solution to meet your application needs.

Oznake: ,

Zadnje novice

 Power spring solves the problem of insulin syringe
Power spring solves the problem of insulin syringe

Čas: 2022-9-14

Mention of diabetes, I think everyone is not strange. Data show that by the end of 2021, the total number of type 2 diabetes in China was about 120 million. When oral hypoglycemic agents are standardized and blood glucose control is still unsatisfactory, insulin injection is an inevitable choice for the treatment of type 2 diabetes. Many may not know...

 Ali poznate vzmetni modul s konstantno silo?
Ali poznate vzmetni modul s konstantno silo?

Čas: 2022-9-14

 Prepričan sem, da mnogi od vas veste, kaj je vzmet s konstantno silo, kajne? Vzmet s konstantno silo je vzmet, ki vzdržuje konstantno silo vzmeti za določen hod, imenovana tudi vzmet s konstantno silo, in se uporablja pri linearnem gibanju, običajno z uporabo svoje odbojne sile. Vzmet s konstantno silo je sestavljena iz kovinske pločevine spiralne oblike, ki je na notranji strani upognjena tako, da...

 Torsion springs: where are they used and why did you choose to utilize them?
Torsion springs: where are they used and why did you choose to utilize them?

Time:2022-12-1

There are many types of springs, but the most common are torsion springs. The design of torsion springs is optimized to maintain maximum rotational pressure between two surfaces, these helical or helical springs are usually adhered to the coils at both suspended ends. These ends are connected to external components, which are then rotated to apply bending stress. Unlike other...

 Gradite sanje skupaj, zdravi partnerji - Qianye natančnost
Gradite sanje skupaj, zdravi partnerji - Qianye natančnost

Čas: 2022-9-13

Ekipa Qianye je prepričana, da je prva prioriteta korporativnega upravljanja Qianye ljubi vsakega zaposlenega. Zdravje zaposlenih je največje bogastvo podjetja, saj zagotavlja zdravje zaposlenih, ustvarja dobro delovno in bivalno okolje ter odraža skrb podjetja za zaposlene. 15. novembra 2021 je podjetje Shenzhen Qianye Precision Metal Co., Ltd. uradno začelo letno brezplačno...

 The QY spring mechanism of manual cordless blinds is very different from ordinary wire springs
The QY spring mechanism of manual cordless blinds is very different from ordinary wire springs

Time:2023-3-6

The QY spring mechanism of manual cordless blinds is very different from ordinary wire springs, and its core component is the need for a spring with negative gradient. Cordless blinds are usually designed to encounter the problem that when the blinds is pulled to the top it will sag and when it is pulled to the bottom it will return to...

 Uporaba vzmeti s spremenljivo silo v maloprodajnih zaslonih
Uporaba vzmeti s spremenljivo silo v maloprodajnih zaslonih

Time:2022-9-3

Variable force springs are very common in the point-of-purchase or POP industry, especially in shelf pushers. Variable force springs provide variable force to precisely match increasing or decreasing force requirements, propelling the product horizontally forward. Due to their wide applicability, these springs can be seen in the tobacco, cosmetic, electronics and medical industries. So why use variable force springs in...

Product