У дома > Блог > [Прецизност Qianye] Дизайн на пружината с постоянна сила в 8 стъпки

[Прецизност Qianye] Дизайн на пружината с постоянна сила в 8 стъпки

източник:Qianye Precision време:2022-9-15

 The пружина с постоянна сила is made of stainless steel strip. The high-strength steel strip is shaped by specific spring production equipment. When it is straightened by external force, the spring will naturally roll back and produce elastic force. However, when our goal is achieved, it can return to the starting point specified by us after displacement.

Пружина с постоянна сила has the characteristic of maintaining constant force in long stroke, and can be applied to products requiring linear movement such as round-trip, sliding, stretching, homing, balancing or labor-saving. For example, we go to the common fan lifting, store display shelves, tape measure, lifting doors and windows and computer monitor lifting. So if you choose a constant force spring suitable for your product, the design has the following 8 steps.

  1. 1. Material selection – most flat steel springs produced by Qianye precision are made of type 301 stainless steel. This material is the most readily available and predictable. Thousands of industry engineers can assist in selecting standard sizes to speed up the process.

    2. Estimated life cycle – the life of constant force spring is very predictable, making it one of the most important considerations. Being realistic is important because it is estimated that a longer life cycle will lead to larger and more expensive designs. Underestimating the life cycle of constant force springs may lead to premature failure. Common life cycles range from 4000 to about 25000 life cycles. If a longer life cycle is required, the tolerance of increasing spring diameter and force due to low stress levels and small differences in materials must be considered.

    3. Establish force – the force of the constant force spring shall be equal to the requirements of the application. The standard tolerance for constant spring force is ± 10%.

    4. Determine the space -. The inner diameter (ID) of the spring depends on the thickness, the life cycle and the required force. The outer diameter (OD) depends on the above, and the total length is taken as an additional consideration. The constant force spring does not extend tangent to the spring body. The standard tolerance for ID and OD is ± 10%.

    5. Calculate the total length – the total length of the spring shall take into account the actual elongation of the spring in application, plus at least enough material to maintain 1-1 / 2 turn on the spring when fully extended.

    6. Select end details – Qianye has many standard end details available. Qianye precision is equipped with a complete tool and mold department, which can create many customized designs required by customers.

    7. Consider the environment – corrosive atmosphere or extreme temperature will affect the service life and material selection of the spring.

    8. Complete the design – once all the above criteria are considered, the spring can be located or inferred.

     Shenzhen Qianye Precision Metal Co., Ltd. is a professional manufacturer of high-precision springs. The company integrates product R & D, production, sales and service. We sincerely welcome new and old customers and friends from all walks of life to visit and negotiate business cooperation. Qianye precision will serve you wholeheartedly!

Последни новини

 Understanding the Mechanics and Applications of Variable Tension Springs
Understanding the Mechanics and Applications of Variable Tension Springs

Time:2023-9-21

Springs are mechanical devices that store and release energy, commonly used in various applications to absorb shocks, maintain tensions, or store energy. One type of spring that has gained significant attention in recent years is variable tension springs. These springs are designed to offer varying levels of tension based on the specific needs of the application. In this article, we...

 China constant force spring factory
China constant force spring factory

Time:2023-4-4

A constant force spring, also known as a clock spring or power spring, is a mechanical spring that exerts a nearly constant force over its range of motion. It is typically made from a flat strip of spring steel wound tightly around a shaft or arbor, which allows it to store and release energy as it is wound and unwound....

 Exploring the Uses and Benefits of Constant Force Springs
Exploring the Uses and Benefits of Constant Force Springs

Time:2023-6-8

Introduction Constant force springs are a type of extension spring that exerts a near-constant force as it is extended or compressed. These springs are widely used in various industries such as aerospace, automotive, medical, and electronics. In this article, we will explore the uses and benefits of constant force springs. Uses of Constant Force Springs 1. Automotive Industry: Constant force...

 Constant force spring in vehicle ashtray
Constant force spring in vehicle ashtray

Час: 2022-9-14

If the plush toys in the car are the favorite of female car owners, it is believed that the favorite of male car owners is the vehicle ashtray. Car ashtrays are indispensable car supplies for smokers. Although the vehicle ashtray is specially designed for smokers' car owners, it can also be used to place sundries for non-smoking car owners, which is...

 What is the development and application of Constant Force Torsion Spring?
What is the development and application of Constant Force Torsion Spring?

Time:2023-7-25

Introduction Torsion springs are a type of mechanical spring that generate rotational forces or torque. These springs are widely used in various applications, including automotive, aerospace, and industrial machinery. In recent years, there has been a growing demand for torsion springs that provide a constant force over a wide range of deflections. This article aims to discuss the development and...

 Creating a Variable Force Spring: A Comprehensive Guide
Creating a Variable Force Spring: A Comprehensive Guide

Time:2023-4-25

Creating a Variable Force Spring: A Comprehensive Guide Springs are widely used in various industrial and household applications. They are essential components that store and release mechanical energy. However, traditional springs have a fixed force, which limits their versatility. In this guide, we will explain how to create a variable force spring, which can adapt to different loads and applications....

Product
 Пружина за карбонова четка
Пружина за карбонова четка
Характеристика: 1. Поради постоянната сила, независимо от дължината на въглеродната четка и комутатора, налягането остава същото. 2. Пружината с постоянна сила намалява въглеродната четка...
 Услуга за оптимизиране на дизайна
Услуга за оптимизиране на дизайна
От идеи за продукти, дизайн до производство на завършен продукт, ние можем да помогнем на клиентите да ги завършат и да помогнем на клиентите да оптимизират своите продукти от професионална гледна точка на използване на пружини, ускоряване...
 Силова пружина
Силова пружина
Характеристика: Силовата пружина е навита от стоманена лента. За ограничаване на външния му диаметър е необходима пружинна кутия. Центърът на пружината е свързан с вала. Кога...
 Пружина с постоянна сила
Пружина с постоянна сила
Характеристика: Пружините с постоянна сила (постоянна сила) се навиват от ленти от неръждаема стомана. Стоманените ленти с висока якост се оформят от специфично производствено пружинно оборудване. Когато външната сила ги изправи,...
 Постоянна торсионна пружина
Постоянна торсионна пружина
Характеристика: Фиксираната (постоянна) въртяща пружина (пружина) е изработена от неръждаема стомана. Външната сила връща главната пружина от нейното естествено състояние към изходното колело (съхранение на енергия). Когато...
 Услуги по сглобяване и монтаж
Услуги по сглобяване и монтаж
Компанията Qianye не само осигурява производството на прецизни пружини, но също така се фокусира върху структурния дизайн и функционалните решения на цялата пружинна система и може да осигури цялостна...